Fitting A Cat Flap

It can be difficult to set up the flap for your cat, but with the right instructions, it's not too difficult. Determine how high you would like the flap to be (normally it's at belly height). Mark this point on the door, and use the template provided as a reference to drill.

If you have a kitten that is still a newborn then gently prop the door slightly open and allow it to pass through. Reward it each time it goes through.

Measure the Door

A cat flap is a great way to allow your pet to move into and out of your home whenever it likes. This can help keep your cat healthy since it will ensure it is getting enough exercise and be able to go back inside when it gets trapped in the elements during bad weather. This will reduce the amount of time you have to let your cat in or out and also make your home secure by notifying you when it's gone.

It is important to make sure that the cat flap is installed correctly to stop your pet from being pushed through it or escaping by other animals (e.g. dogs). It is important to measure the height of your pet's belly and the entrance to your home to make sure that the flap is at the right height. You can adjust the height of your flap in case your cat is smaller or taller than average.

The next step is to utilize a spirit level mark the centre of the door where you will install the flap. Utilizing the marking as a guideline, you can use an jigsaw to cut the shape of the flap inside the door. After you've cut the area out and sanded the edges to create smooth surfaces. Make any holes that are required.

The installation of a cat flap should not take more than two hours. However, the process may be slightly more complicated if you need to fit it onto a uPVC or composite door since these doors come with an array of thicknesses, which affect how the holes are cut and the type of door they are fixed into. We always recommend to consult with an expert for your first time working with glass.

Measure Your Cat

A cat flap can save you from hearing your pet's cries for you to let it in or out. This is particularly helpful for those who work most of the day and your cat has to stay inside waiting until you get home regardless of the weather.

It is essential to measure your cat first before attempting to install. Although it might seem like to be a simple task, it is essential to measure the right way or your cat will be unable to use.

First, ensure that your cat is calm prior to taking measurements. You'll need to keep your cat flap fitting in a position in which they cannot move. Also, make sure that the measuring tape is flat and not curved against their body. Holding the ruler or measuring tape against their body from the top of their head to the bottom of their tail can allow you to make an exact measurement.

Once you've determined your cat's measurements then you can look at the door to decide where to put the flap. It is advisable to position the flap at the height of your cat's belly because this will help them to pass through it without much effort. This will also prevent the flap from making a lot noise as it swings back and back.

It is also important to think about the thickness and the structure of the upvc door panels with cat flap door or composite. Although timber doors are of the same thickness, uPVC and composite doors can be very different in their overall design and this can make the installation of a cat flap more complicated since you have to make sure that the hole you make is the proper size for your pet.

It is also worthwhile looking through the instructions included with the kit to locate a template drawing that can be used to mark the location of the hole inside the door. This will allow you determine where the opening needs to be, and also to ensure that the template is placed correctly on the door. It is also helpful to employ a spirit-level to ensure that the template sits flush against the door.

Cut the Flap

You'll need to cut a hole in the door panel for your cat flap before you can put it in place. This can be a tricky job, and it is recommended to get help from a professional cat flap fitting service to complete this task if you don't have the knowledge or skills to complete the task yourself. You can also refer to the instructions provided with the kit to learn how to do it correctly.

You can take the height of your cat's or kitten's stomach as a guide. A good rule of thumb is to set the flap of your cat about 10 centimeters away from the ground since this is roughly the average height of the cat's belly. This will let your cat pass through the flap with ease and make it more difficult for other cats or nosy neighbors to get in or out.

The position of the cat flap on the door with pencil. Next, if your kit includes a paper template, lay it over the door and use the marks to drill holes into every corner of the template. You will then be able to cut out the design of the template and replace it with your cat flap fitting flap.

If you are installing your cat flap in the form of a door made of wood or uPVC, you are able to do this yourself if you feel confident enough to handle using a Jigsaw. Be cautious not to cut into the mullions or rails that run vertically of your door. You can use a jigsaw to cut your panel into a square or a circle according to the way you'd like it. Take your time, and don't try to force the jigsaw to cut faster.

Once the hole is cut, carefully fit the flap onto its new location and make sure that it is firmly secured. If the flap has screw caps then push them into the protruding bolts. Once the screws are in place, sand any rough edges of the cut then seal any gaps to ensure that there are no draughts coming into your home.

Place the Flap

If you have a basic cat flap, you can leave it open and encourage your pet to use it by placing a small amount of cat food in the front of the door. You can also try pushing the fitting cat flap in upvc door panel through using your hand or a stick. Once your cat has become accustomed to walking through the flap it will be in a position to move as it pleases. This allows you to let it in and out whenever it wishes.

It is possible to fit the flap inside an UPVC door or glass door, but it might not be as simple as putting one in a wooden external door. This is because the UPVC doors and certain types of glass doors do not have an even thickness. This could have an enormous impact on how you cut out the flap hole and also how well the flap fits after installation.

Depending on the type of cat flap you select It may include a mounting kit as well as a template that will show precisely where to drill the holes for it. If the kit doesn't include a template you can copy it to create your own. When cutting, it's important to keep the jigsaw from being pushed too far enough to make a larger hole than is necessary in your door.

Most cat flaps are square or rectangular in shape but there are also some which are circular, and they are generally more difficult to place. If you have a circular flap it is essential to ensure that the hole is in the proper position on your door, because if it's not, the cat won't be able to use it and may be stuck in the open all day (or even at night).

Some cat flaps have locks which allow you to regulate when your cat comes in and goes. These are very helpful in the event that you are concerned about your cat going out at night only to come back in because of the darkness, or you're working all day. Certain locks can be used for either entry or exit, and others can be locked both ways. This is beneficial for sick or older cats who don't want to go outside in bad weather.